Kamis, 25 Maret 2010

CCNA 1 Chapter 11 (B)

1. Refer to the exhibit. A student working in the lab selects a cable that is wired as shown. Which connection types can successfully be made with this cable? (Choose two.)
• connecting a PC to a router’s console port
• xxconnecting two routers together via their fast ethernet ports
• xxconnecting two switches together at gigabit speeds
• connecting a PC to a switch at Gigabit Ethernet speeds
• connecting two devices with the same interface type at Fast Ethernet speeds

2. Which three statements are true about the role of routers in the network? (Choose three.)
• They propagate broadcasts.
• They enlarge collision domains.
• They segment broadcast domains.
• xxThey interconnect different network technologies.
• xxEach router interface requires a separate network or subnet.
• xxThey maintain a common frame format between LAN and WAN interfaces.

3. Refer to the exhibit. A network administrator has decided to use packet capture software to evaluate all traffic from the student subnet on the way to the Internet. To ensure that all packets are captured, what network device should be used to connect the monitoring station to the network between R1 and R2?
• xxrouter
• hub
• switch
• wireless access point

4. A network administrator is required to use media in the network that can run up to 100 meters in cable length without using repeaters. The chosen media must be inexpensive and easily installed. The installation will be in a pre-existing building with limited cabling space. Which type of media would best meet these requirements?
• STP
• xxUTP
• coaxial
• single-mode fiber
• multimode fiber

5. Refer to the exhibit. Which three statements are true about the exhibited topology? (Choose three.)
• Hosts B and C are in the same subnet.
• xxFive broadcast domains are present.
• xxHost B is using a crossover cable to connect to the router.
• Four broadcast domains are present.
• xxFive networks are shown.
• Host B is using a rollover cable to connect to the router.

6. Which three types of connectors are commonly associated with Cisco’s V.35 serial cables? (Choose three.)
• RJ 11
• xxDB 60
• xxWinchester 15 pin
• DB 9
• xxsmart serial
• RJ 45

7. How many host addresses may be assigned on each subnetwork when using the 130.68.0.0 network address with a subnet mask of 255.255.248.0?
• 30
• 256
• xx2046
• 2048
• 4094
• 4096

8. Refer to the exhibit. Based on the IP configuration shown, what would be the result of Host A and Host B attempting to communicate outside the network segment?
• both host A and B would be successful
• xxhost A would be successful, host B would fail
• host B would be successful, host A would fail
• both Host A and B would fail

9. Refer to the exhibit. What destination IP address will PC1 place in the header for a packet destined for PC2?
• 192.168.1.1
• 192.168.2.1
• 192.168.2.2
• 192.168.3.1
• xx192.168.3.54

10. Refer to the exhibit. Which three statements identify the type of cabling that would be used in the segments that are shown? (Choose three.)
• Segment 1 uses backbone cabling.
• xxSegment 1 uses a patch cable.
• Segment 3 uses patch cabling.
• Segment 3 uses vertical cabling.
• xxSegment 3 uses horizontal cabling.
• xxSegment 4 uses vertical cabling.

11. A company is planning to subnet its network for a maximum of 27 hosts. Which subnet mask would provide the needed hosts and leave the fewest unused addresses in each subnet?
• 255.255.255.0
• 255.255.255.192
• xx255.255.255.224
• 255.255.255.240
• 255.255.255.248

12. Refer to the exhibit. A student is setting up a home network primarily used for extensive file transfers, streaming video, and gaming. Which network device is best suited to these types of activities in the topology shown?
• wireless access point
• router
• hub
• xxswitch

13. Refer to the exhibit. How many subnets are required to support the network that is shown?
• 2
• xx3
• 4
• 5

14. What does the term “attenuation” mean in data communication?
• xxloss of signal strength as distance increases
• time for a signal to reach its destination
• leakage of signals from one cable pair to another
• strengthening of a signal by a networking device

15. To establish a console connection from a computer to a Cisco router, which cable wiring option would be used?
• xxcrossover cable
• straight through cable
• rollover cable
• V.35 cable

16. What makes fiber preferable to copper cabling for interconnecting buildings? (Choose three.)
• xxgreater distances per cable run
• lower installation cost
• xxlimited susceptibility to EMI/RFI
• durable connections
• xxgreater bandwidth potential
• easily terminated

17. Refer to the exhibit. A network technician has been allocated the 192.168.1.0/24 private IP address range for use in the network that shown in the exhibit. Which subnet mask would be used to meet the host requirements for segment A of this internetwork?
• xx255.255.255.128
• 255.255.255.192
• 255.255.255.224
• 255.255.255.240
• 255.255.255.248

18. Which subnet mask would be assigned to the network address of 192.168.32.0 to provide 254 useable host addresses per subnetwork?
• 255.255.0.0
• xx255.255.255.0
• 255.255.254.0
• 255.255.248.0

19. What type of network cable is used between a terminal and a console port?
• cross-over
• straight-through
• xxroll-over
• patch cable

20. Which option identifies the primary interface which would be used for initial configuration of a Cisco router?
• AUX interface
• Ethernet interface
• serial interface
• xxconsole interface

21. What are three common methods for setting a UTP Ethernet port to MDI or MDIX operation? (Choose three.)
• direct configuration of the device
• xxcable color code association
• cable selection and configuration
• use of cable testers to determine pinouts
• xxthe enabling of the mechanism to electrically swap the transmit and receive pairs
• xxthe automatic detection and negotiating of MDI/MDIX operation of the port

22. Which device is used to create or divide broadcast domains?
• hub
• switch
• bridge
• xxrouter
• repeater

23. Refer to the exhibit. Assume that all devices are using default settings. How many subnets are required to address the topology that is shown?
• 1
• 3
• 4
• xx5
• 7

Tidak ada komentar:

Posting Komentar

 
Home | Gallery | Tutorials | Freebies | About Us | Contact Us

Copyright © 2010 exam ccna |Designed by Templatemo |Converted to blogger by BloggerThemes.Net

Usage Rights

DesignBlog BloggerTheme comes under a Creative Commons License.This template is free of charge to create a personal blog.You can make changes to the templates to suit your needs.But You must keep the footer links Intact.